设为首页   收藏本站
 
 
  天津市科器高新技术公司  
 
网站首页 | 关于科器 | 科器资讯 | 产品中心 | 加盟我们 | 客户服务 | 招贤纳士 | 联系我们
 
 
 
产品中心
 
  粉末压片机
  振动磨
  模具
  液相色谱仪
  光泽度仪
  红外附件及其他
 
 
 
     
 
 
 
大振动磨-ZDM系列
 
 
ZDM-100 振动磨(双速)
 
 
产品型号: ZDM-100 振动磨(双速)
产品服务: 产品使用说明书下载
产品视频: 在线观看    视频下载
产品经理: 刘俊君 路琦
产品专线: 022-27350692 27350624 27342120
 
 

ZDM-100 振动磨(双速)

 

1、振动磨盖Cover of Vibratory Grinding Mill

2、固定手柄Fixed handle

3、固定盘Fixed disk

4、时间继电器Time relay

5、急停按钮Emergency stop button

6、启动按钮Start button

7、保护开关Protection switch

8、磨盒Grinding case

9、小冲击锤Impact rammer

10、磨盒盖Cover of grinding case

11、样品Sample

12、小冲击锤Impact rammer

13、O型密封圈O-Shaped seal ring

 

应用范围  The scope of applicati

 

该仪器主要应用于X射线荧光光谱仪配套的设备,该设备操作方便,性能稳定,效率高,噪声小,无粉尘泄露,可替代国外同类产品。

The instrument is mainly used in X-ray fluorescence supporting equipment, the equipment easy to operate, stable performance, high efficiency, low noise, no dust leaks, can replace similar foreign products.

 

操作说明 Operating Instructions 


1. 装样Holding Sample
  
 1.1 将击锤放入磨盒中,再将样品放在磨盒击锤

Put impact rammer into the grinding case, and then put sample between grinding case and impact rammer.
    1.2. 研
磨盒中的品量5~15cm 3。

Quantity of sample in grinding case shall be 5~15cm3.
〈警告〉当
放入磨盒中的品量≤5cm 3时会损磨盒 

In case quantity of sample put into the grinding case is ≤5cm3, it may damage the grinding case.

 

2. 时间设Time Setting


2.1. 按时间继电器上下行按时间。其中中的一位表示时间单位:小H)、分钟M)和秒(S)

Press two buttons at upper and lower rows on the Time Relay, set the running time, of which the middle digit indicates time units: hour (H), minutes (M), and seconds (S).
2.2. 碳
磨盒,一般定在3分钟,高铬钢磨盒,一般定在10分钟

Generally set within 3 minutes for grinding case of tungsten carbide, 10 minutes for that of high chrome.

 

3. 制样 Specimen Preparation


3.1. 将研磨盒放在振磨的固定上,旋固定手柄。2。盖紧磨的盖,按振磨的绿启动启动磨。

Put the grinding case on the fixed disk of Vibration Grinding Mill, screw the fixed handle. See Fig.2. Fasten down the cover of Vibration Grinding Mill, press green start button of it. Start Vibration Grinding Mill.
3.2. 如果发
生意外情立即按下色急停按

If something unexpected happened, please press red emergency stop button immediately.
〈警告〉在机器完全停稳
前,不要打磨的盖 

Do not open the cover of Vibration Grinding Mill before the machine completely stopped.
3.3. 机器停稳
后,打磨的盖,取出磨盒。将样品倒入过滤筛中,80%样品的粒度≤80um。After the machine completely stopped, open the cover of Vibration Grinding Mill, take out the grinding case. Pour sample into filter sieve, particle size of 80% sample should be in ≤80um.
3.4. 如果研
磨后的品,不到3.3. 的要求。取出研磨盒,自然冷却至60℃以下,再继续工作。找出最佳时间

In case the sample after grinded can’t reach the requirement described in Item 3.3, take out the grinding case, cool it to less than 60℃ in room temperature, and work continuously. Find out optimum grinding time.

 

技术指标 Indicators

 

ZDM-100

技术参数

进料粒度

10mm3

出料粒度

80um(或200目)

进 料 量

10 ~ 30cm3

   

380V/50Hz

额定功率

1.3/1.8 KW

   

(1400或900)r/min

研磨时间

0~999秒

磨盒容积

100cm3

磨盒材料

碳化钨或高铬钢

外型尺寸

650 x 550 x 950mm

   

170㎏